Keypad Programming

\r\n

\r\nProgramming the Keypad \r\n

\r\n

\r\n** If you need to clear an existing PIN, press and hold in order. \r\n

\r\n
    \r\n
  •          PROG, 6, UP/DOWN ARROW
  • \r\n
\r\n
\r\n
    \r\n
  1. Press in order: 3 5 7 PROG 
  2. \r\n
  3. Enter your PIN and press the [PROG] button.
    \r\n    -Red LED blinks once per second.
  4. \r\n
  5. Press the [PROG] button a second time.
    \r\n    -Red LED blinks twice per second.
  6. \r\n
  7. Press the total number of Doors you wish to control.
    \r\n (Press either [2] or [3])
  8. \r\n
  9. Press the [PROG] button a third time.
    \r\n     - Red LED blnks several times and turns off.
  10. \r\n
\r\n
\r\n

\r\nProgramming the Door Openers \r\n

\r\n
    \r\n
  1. Decide which door will be Door #1, #2 and #3.
    \r\n -Learn Code Indicator LED (on opener) blinks.
  2. \r\n
  3. Enter your PIN and press the arrow up/ arrow down triangle button.
    \r\n -Learn Code Indicator LED continues to blink.
  4. \r\n
  5. Press the number you have picked for this Door Opener [1], [2], or [3].
    \r\n -Learn Code Indicator LED stays on.
  6. \r\n
  7. Press the arrow up/arrow down triangle button a second time.
    \r\n -Learn Code Indicator LED turns off.
  8. \r\n
  9. Pressthe arrow up/arrow down triangle button a third time.
    \r\n -Door should move.
  10. \r\n
\r\n

\r\nRepeat Steps 1 thru 5 for each door opener. Each door opener must be programmed to receive the signal from the wireless keypad. \r\n

\r\nTROUBLE SHOOTING:  \r\n
    \r\n
  • If the garage door does not move, check the red LED on the keypad.
  • \r\n
  • If the LED is blinking rapidly, the PIN was entered incorrectly.
  • \r\n
  • Any keypad button will control the door for 30 seconds after the door starts moving.
  • \r\n
  • Rapid blinking of the LED indicates an error. After a few seconds the LED will turn off and then you can try again.
  • \r\n
  • If the red LED does not blink during use, the battery needs to be changed.
    \r\n
  • \r\n
\r\n

\r\nMounting Instructions \r\n

\r\n
    \r\n
  • Remove battery cover.
  • \r\n
  • Drill a 1/16" hole for the top mounting screw.
  • \r\n
  • Install a screw into the top drilled hole, leaving a 1/8" gap between the screw head and the wall.
  • \r\n
  • Hook the keypad over the screw.
  • \r\n
  • Mark the bottom hole then screw in the bottom screw.
  • \r\n
  • Reinstall the battery cover.
    \r\n
  • \r\n
\r\n

\r\nAdditional Assistance:
\r\n
\r\nShould you need additional information please contact our customer service department at
\r\n1-800-275-6187. \r\n

\r\n

\r\n \r\n